These piezoelectric multicomponent dynamometers are for measuring the three orthogonal components Fx, Fy and Fz of a force.
The Kistler 9139AA is a piezoelectric multicomponent dynamometer that measures the three orthogonal force components Fx, Fy, and Fz up to ±6,744 lbf (±30 kN), on a 5.51 × 7.48 in (140 × 190 mm) cover plate. Its stiff, robust build suits high-performance cutting, while piezoelectric sensors resolve forces down to <0.01 N. It can also be wired for six-component force and moment measurement.
IP67: with connecting cables 1687BA5, 1689BA5, 1677BA5, or 1679BA5
What it is used for
Some of the use cases for the 9139AA include:
Milling — cutting force measurement in high-performance applications
Surface grinding — multicomponent force measurement
Drilling — thrust and lateral force measurement
Large forces — general multicomponent force measurement
Main features / advantages
Wide measuring range
Patented and largely temperature-compensated design
Compact and very robust design
High natural frequency
What does the 9139AA measure?
The 9139AA is a piezoelectric multicomponent dynamometer for measuring the three orthogonal components Fx, Fy, and Fz of a force.
By using piezoelectric force sensors, the dynamometer not only measures large forces but can also accurately measure small forces in the newton range. The high natural frequency and high sensitivity of piezoelectric sensors permit high-quality measuring signals from very dynamic processes in machining or general force measurement.
The dynamometer consists of four 3-component force sensors mounted under high preload between the cover plate and the two lateral base plates. This special mounting gives a low temperature error. Each force sensor contains three crystal rings: one sensitive to pressure in the y-direction and two sensitive to shear in the x- and z-directions. Forces are measured practically without displacement. The outputs of the four sensors are fed to the 9-pole flanged socket, and multicomponent force-moment measurements are also possible.
The four sensors are ground-isolated, which largely eliminates ground loop problems. The dynamometer is corrosion-resistant and protected against penetration by splashing water or cutting fluid, and with connecting cable Type 1687BA5 or 1677BA5 it meets degree of protection IP67.
Why engineers pick it
Large forces and small forces on one plate. The range covers ±30 kN, with calibrated partial ranges down to 0 … 300 N and a threshold below 0.01 N.
Temperature errors kept low. The patented sensor mounting is largely temperature compensated.
Dynamic cutting processes. Natural frequencies of about 2.9 to 3.0 kHz and high piezoelectric sensitivity capture very dynamic machining forces.
Shop-floor ready. The dynamometer is corrosion-resistant and protected against splashing water and cutting fluid, reaching IP67 with the specified cables.
For data acquisition and analysis, the DAQ system Type 5697A1 with DynoWare software, or a LabAmp Type 5167A with integrated DAQ, completes the measuring chain.
How is the 9139AA mounted?
The dynamometer mounts with eight screws to any face-ground, clean surface, such as a machine tool table, or on a magnetic plate. Workpieces and force-introducing parts clamp into M10 tapped blind holes in the cover plate, or from below. Their contact surfaces must be surface ground for good mechanical coupling. Eight M10x60 mounting screws and a stainless steel waterproof cover for the Fischer connector are included.
When is the 9139AA the wrong choice?
Uneven mounting surfaces. An uneven contact surface causes internal distortion, adds stress on the measuring elements, and increases crosstalk.
Simultaneous loading at full range. When components act simultaneously, the range is ±20 kN (force vector centrical, 71 mm above the dynamometer, with no moments).
High-frequency processes on heavy fixtures. Natural frequency is about 3 kHz without additional mass, so workpiece and fixture mass lower the usable bandwidth.
9139AA FAQ
±30 kN (±6,744 lbf) in Fx, Fy, and Fz as a single component, and ±20 kN when components act simultaneously.
Yes. With an 8-wire cable and an 8-channel charge amplifier, Mx, My, and Mz can be measured along with the forces.
The threshold is below 0.01 N.
About 2.9 kHz in x and y and 3.0 kHz in z, without additional mass.
The mounting surface (cover plate) is 140 × 190 mm. The dynamometer weighs about 12.9 kg (28.4 lb).
Eight M10x60 mounting screws (65012838) and a stainless steel waterproof protective cover for the Fischer connector (1431A1).
Configure and order the 9139AA
Choose the 9139AA with the cable for 3- or 6-component measurement and order directly on this page. For questions, contact us.
Kistler - 9139A: Multicomponent Force Sensor Family